Search Results

The author surveys some of the general conditions prevailing in the street-railway field and the prospective development of a new type of service, in discussing the necessity for closer cooperation between the engineers of the automotive industry and the operating organizations of the railways, the idea being to develop flexible transportation-equipment that will coordinate with the operation of present railway-transportation facilities and to promote the utilization, wherever feasible, of railway power-supply in the employment of flexible bus-type equipment in supplementing and extending railway-organization service. Changing conditions are outlined, the influences tending toward flexible equipment are stated, and the differences of engineering practice pertaining in the railway and automotive fields are commented upon to show wherein railway and automotive engineers can cooperate.

A tract comprising several acres of “tamarack” swamp, drained with tile the previous fall and cleared of stumpage the following spring, was utilized to obtain accurate information regarding the tractor and the plowing equipment required for the heavy operations of first breaking of the peat soil, which was from 5 to 7 ft. deep. The paper describes the equipment used, gives details of the procedure and presents the data that were obtained. Three different types of tractor and two types of plow, the latter having either a marsh or a breaker bottom and equipped both with and without a furrow pusher were used. Specifications of the tractors and the plows are given and commented upon, graphs and tabulations of the results being presented also. Power requirements on timbered peat and on grass marsh are compared and the efficiency of the plowing equipment is discussed.

The five types of final-drive now in use on motor vehicles are stated by the author to be (a) the chain-and-sprocket, (b) the bevel-gear, (c) the worm-gear, (d) the double-reduction and (e) the internal-gear. The advantages of each type as emphasized by its maker are presented and commented upon, and the same procedure is followed with reference to their disadvantages. Following these comparisons of the different drives, which cover about the first third of the paper, the bearing loads and shaft stresses of typical semi-floating and full-floating axles are calculated for the conditions (a) maximum torque plus the normal radial-load on the wheel, (b) the wheel locked and skidding forward when the brakes are applied and (c) the wheel skidding sidewise while the truck is moving. A tabulation of the results obtained from the mathematical calculations is included.

The author (Chicago Tractor Meeting paper) divides the history of the application of mechanical power to farm work into three periods, reviews each one and comments upon the various phases of progressive development that influence the type of tractor most desirable for satisfying present needs. The requirements of farm work are outlined, and the different types of tractor built and being constructed to meet these demands are reviewed, discussion of large versus small tractors, type of drive, power needed, control, methods of operation and the factors constituting general-purpose service being included. So far as adopting the tractor for farm usage is concerned, the author believes that the present limitation of such utilization lies with the tractor industry and with tractor engineers, rather than with the farmer.

The author enumerates the distinctive features of buses designed for city, for inter-city and for country service and comments upon them, presenting illustrations of these types of bus. Steam and electric motive power are discussed and the chassis components for bus service are considered in some detail. The general types of bus body are treated, together with the influences of climatic conditions and local preferences. Comfort and convenience factors are discussed at some length and the problems of heating, lighting and ventilation are given constructive attention. Fare-collection devices and methods are commented upon, and the State and local legal regulations are referred to in connection with their effect upon bus operation. Illustrations are included and a table showing condensed specifications for city buses is presented.

Stating that asphalt, brick and concrete-slab road-surfaces are the only pavements that have given satisfaction for automobile traffic, the author believes further that thus far the concrete-slab surface is the only one worthy of consideration for such traffic. He discusses the merits and demerits of these surfaces and includes an enumeration of the factors that combine to produce a thoroughly satisfactory road surface. Passing to a detailed review of the bearing value of soils and the correction of road failures, the author presents data and illustrations in substantiation of his statements and follows this with a consideration of the reinforcing of a concrete road-slab with steel.

The paper treats of the service, commercial and technical aspects of the subject in turn. The author calls attention to the fact that there can be no such thing as free service, because the customer pays in the end, and gives a specific definition of service. He argues that the engineering departments should urge upon merchandising departments intelligent distribution through dealers, the stocking of an adequate supply of parts and the maintaining of a well qualified mechanical force for the purpose of making engineering development work in the form of farm power automotive apparatus effective. There is a great need for a suitable system of training mechanics for tractor service work, and there should be a definite plan to assure that men making repairs and adjustments in the field are well qualified.

To test tractors for results valuable to the user, the reliability, durability, power, economy and utility should be determined. Standard tests measuring tractor utility and reliability are impossible practically and durability tests would be an extensive project, but tractor and engine-power tests and tests of the amount of fuel required for doing a unit of work can easily be made. The University of Nebraska tests described were for belt and drawbar horsepower and miscellaneous testing for special cases. The four brake-horsepower tests adopted are stated. Tractor operating conditions are then reviewed. The drawbar horsepower tests include a 10-hr. test at the rated load of the tractor, with the governor set as in the first brake-horsepower test, and a series of short runs with the load increased for each until the engine is overloaded or the drive wheel slips excessively, to determine the maximum engine horsepower.

The best weight for a tractor of given horsepower must be a compromise based upon a mean of the many conditions to be encountered by a given machine or by different machines of the same model. While the weight logically will bear some relation to the drawbar pull, the latter in turn depends upon tractor speed. The next item is weight distribution, which requires the utmost skill of the designer; this is elaborated and diagrams are shown of tractors operating in comparatively firm and in soft ground, ascending a grade and when the drive-wheels are mired. The four-wheel-drive tractor requires a modification of the foregoing analysis and the diagrams are applied to afford a similar analysis for this type. The author's conclusion is that, while careful engineering will make the light-weight tractor of conventional type stable under most conditions, there is a possibility that any future trend toward lighter machines will open the field to other types.

Three distinct types of wheel equipment are best able to meet conditions in the field; the pyramid lug, the spade lug and the angle-iron cleat. The author mentions the merits of each type of lug, discusses slippage and states that no one kind of wheel equipment can be recommended as a universal type.

In investigating the forces that tend to break up and destroy roads, the most destructive of these being that of impact, the United States Bureau of Public Roads devised a method of receiving the impact of a truck on a small copper cylinder and determining its amount by measuring the deformation of the cylinder. The impact values are largely dependent upon the type and construction of the truck. Unsprung weights have a great influence upon the impact value of the blow on the road surface and a reverse influence upon the body of the truck; these effects are in two different directions. The present aim of the Bureau is to investigate this impact and the effect of the unsprung weight on the road. Most of the tests have been made on solid tires, a few have been made on worn solid tires and some on pneumatic tires. The Bureau intends to elaborate all of these tests, including different types of pneumatic tire, different unsprung weights and special wheels, such as cushion or spring wheels.

In the past the majority of trucks have been equipped with wood wheels. These gave good service, but the results demanded under strenuous modern conditions seem, the author states, to make the substitution of steel wheels on medium and heavy-duty trucks imperative. Truck engineers and builders seem to recognize the fact, but to hesitate to make the change, chiefly because a metal wheel is somewhat higher in first cost and because some designs have not as yet rendered the service expected of them. The service return of metal wheels is given from the records and reports of the London General Omnibus Co. and the Fifth Avenue Coach Co., both of which use steel wheels exclusively. The added mileage is in excess of wood-wheel service and exceptional tire mileage is shown. The author states briefly the arguments for the hollow-spoke, hollow-rim, the hollow full-flaring spoke and the integral-hub metal wheels.

THE United States was practically unprepared in the field of military motor-transport at the beginning of the war. Due largely to the cooperation of the Society of Automotive Engineers and its members individually, this handicap was overcome and a position stronger in this respect than that of any of the other belligerents was attained. The early efforts and the cooperation between the Society and the various Government departments are described, especially with reference to the Quartermaster Corps which at that time had charge of all motor transportation. Regarding the Class B truck, it is shown that the Society acted as a point of contact between the various members of the industry and the War Department and, although not fostering any program or plan of its own, it was largely responsible for the success of the standardization program conceived and carried out by the Army.

The authors advance for discussion some important problems in the construction of airplanes for military use in this country. The functions of military airplanes designed for strategical and tactical reconnaissance, control of artillery fire and for pursuit are outlined. Problems in construction with reference to the two-propeller system, methods of reducing vibration, application of starting motors, details of the gasoline supply-system, metal construction for airplanes, flexible piping, desirable characteristics of mufflers, shock absorbers, landing gear, fire safety-devices, control of cooling-water temperature, variable camber wings, variable pitch propellers and propeller stresses, are all given consideration. The paper is concluded with suggestions for improvement in design relating to the use of bearing shims, the rigidity of crankcase castings, interchangeability of parts and better detail construction in the oiling, ignition, fuel supply and cooling systems.

The author states as his object a review of what has been done and what must be done to make tractors successful in operating on low-grade fuels, especially kerosene. He takes up in order the four principal methods in common use of applying heat to vaporize kerosene, pointing out the advantages and disadvantages of each method and of its modifications. The author then cites various experiments with different types of carbureters in burning kerosene, drawing at length upon his own experience in this connection. He cites difficulties with gas distribution, manifold condensation, pistons and spark-plugs and points out that carbureter design is inseparable from considerations of tractor engine and manifold design. That better progress has not been made in the past in developing kerosene-burning tractor engines is stated to be largely owing to the fact that there has not been sufficient cooperation between engine and carbureter manufacturers.